Schedule Today

 

Almost everyone maintains their own individual piece of advice about Tools You Need to Install a New Bathtub .

Mounting a bath tub isn't precisely brain surgery, however it does call for strong plumbing, carpentry, and also often, tiling skills. Replacing an old tub with a new one is additionally a moderately challenging job. If the old bathtub is conveniently available, the task can relocate immediately; if you need to open up a wall to eliminate the old bathtub as well as place the brand-new bathtub, the task is much harder. In either case, the job is within a house handyman's skills, although you will certainly need an assistant to move out the old tub as well as set in the brand-new one. Ensure you have qualified on your own for the work and also are comfortable trying it. Rather than working with a service provider to take over a halfway-completed project, it is far better to take into consideration employing one before you begin. Possibilities are you may require a professional plumber to make tube links.
This article will certainly aid you install a brand-new bath tub in your bathroom if you have currently bought a new tub as well as don't need to alter the arrangement of your previous supply of water pipelines.
Your devices and product checklist ought to make up the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipeline Caps


 

Planning for the Setup

First of all, the supporting structure supplied with the bath should be fitted (if called for) according to the maker's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to make sure that if the faucet features a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets unit to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of both taps using 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Ensure you utilize all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom should now prepare to be fitted in its last placement.

 

 

Removing Old Taps

If you require to change old taps with new ones as a part of your setup, after that the first thing you ought to do is separate the water. After doing so, activate the faucets to drain any type of water staying in the system. The process of removing the existing taps can be rather troublesome due to the limited access that is often the case.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a fabric ready for the continuing to be water that will certainly originate from the pipelines. Once the supply pipelines have actually been eliminated, utilize the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from transforming throughout this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old sealing substance.
Prior to proceeding to fit the new faucets, contrast the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.

 

 

Setting up the Bath tub

Using the two wood boards under its feet, put the tub in the called for position. The wooden boards are helpful in evenly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 tiny points.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by checking the level and also adjusting the feet on the bathtub till the level checks out level.
To mount faucets, fit the bottom of the furthest flexible faucet port to the proper supply pipe by making a compression sign up with; after that do the exact same for the various other faucet.
Switch on the water supply and examine all joints as well as brand-new pipework for leaks as well as tighten them if necessary. Fill the bathtub as well as additionally inspect the overflow outlet as well as the typical electrical outlet for leakages.
Finally, take care of the bathroom paneling as defined in the supplier's instruction manual. Tiling as well as sealing around the tub ought to wait up until the tub has actually been utilized a minimum of once as this will resolve it right into its final placement.

 

 

Suitable New Taps

If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end provides a link to the current supply pipes.
If you require to fit a monobloc, after that you will require lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the placing hole in the bath/basin ensuring that the washing machines remain in location in between the faucet and the sink. Secure the faucet in position with the supplier offered backnut. When the tap is firmly in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical faucet adapters. The former type needs to be linked to the tap finishes first, tightening just by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have been attached.

 

 

Tiling Around the Bathtub

In the location where the bathroom satisfies the tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to fracture an inflexible seal, triggering the water to penetrate the wall between the bathroom and also the tiling, bring about issues with wetness and also possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your components as well as fittings. They are sold in tubes and cartridges, as well as are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly load the bathtub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can split relatively very early if you do not take into account this movement before securing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally conveniently available on the market. It is a good idea to fit the tiles using waterproof or waterproof glue as well as grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

As an enthusiastic reader on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I thought sharing that piece of writing was a great idea. Enjoyed our piece of writing? Please share it. Let somebody else check it out. Kudos for your time. Don't hesitate to stop by our blog back soon.

Go Company